Modern PE and nylon gas mains are invisible to standard electromagnetic locators. HR Utilities uses tracer-wire detection and non-destructive digging to locate gas distribution networks across Melbourne and Victoria — to Energy Safe Victoria requirements.
The gas distribution networks installed across Melbourne and regional Victoria over the past three decades are predominantly polyethylene (PE) or nylon — not steel or cast iron. That distinction is critical: PE and nylon are non-conductive, so the electromagnetic induction method that reliably traces metallic pipes simply does not work on them.
A locator may trace a usable tracer wire installed alongside a PE main. Where the wire is absent or damaged, discuss other field methods and targeted physical exposure. Confirm safe access, the investigation limits and asset-owner conditions before selecting the approach.
There is a further complication: gas services connecting premises to the distribution main are frequently absent from Before You Dig Australia (BYDA) plans. The standard industry position is to assume a gas service is present and treat the area accordingly until the ground is proved clear. Our locating process is built around that assumption.
Gas is a hazardous service. Victorian law sets specific obligations for anyone working near gas infrastructure — before, during, and after excavation.
Non-conductive — not detectable by electromagnetic induction. Tracer-wire detection or non-destructive digging required.
Steel and cast-iron distribution mains are electromagnetically traceable. Depth estimation via signal-strength analysis.
A locator traces a usable conductive wire and records the detected route. Confirm location uncertainty and the quality level supported by the investigation evidence.
Targeted exposure can provide direct evidence of pipe position. Confirm the method and controls with the asset owner and site team; vacuum excavation still carries risks.
Check the WorkSafe and Energy Safe Victoria guide for the applicable work controls. Confirm any spotter requirement and plant-specific registration before excavation.
Follow the site's emergency plan and contact the asset owner from a safe location. Leave the site undisturbed unless safety requires otherwise, as advised by the WorkSafe and Energy Safe Victoria guide.
The WorkSafe Victoria and Energy Safe Victoria guide sets restrictions for both mechanical and manual excavation near gas assets. Obtain the asset owner's conditions and any required written permission before work; hand digging is not a blanket exception.
Transmission pipelines have separate owner requirements. Confirm the service type, pressure, location evidence and proposed work method with the owner. Use our No-Go Zones commissioning checks to prepare the brief, then apply the guide and project conditions.
A gas strike can put lives at risk. If you suspect damage or a gas escape, follow the site's emergency plan and the guidance below:
Notify the person responsible for the site and follow the emergency plan's reporting arrangements. Consult the asset owner and relevant regulator about any incident notification or site-preservation requirements.
A four-stage process from records review to locating evidence for your work plan. Confirm permissions and site controls before excavation.
We review available gas network plans, easement data and site history. Confirm who will lodge the BYDA enquiry and supply the asset-owner responses before fieldwork.
Our NULCA-certified locators energise the tracer wire installed alongside PE/nylon gas mains and trace its route to surface, marking the pipe position with survey-grade GPS.
Discuss targeted exposure where detection cannot resolve the required position or depth. Confirm asset-owner permissions, the work method and controls before excavation.
The confirmed gas main position is delivered as a CAD plan, GIS file, or PDF overlay georeferenced to MGA and AHD, with AS5488 quality level attributed to each detected feature.
Any ground disturbance within or near a gas easement or known service area requires a BYDA enquiry and, where plans are indicative or absent, field locating before plant moves in. The utility locating process escalates from QL-D (BYDA plans) to QL-B (field-detected and marked) to QL-A (physically exposed) depending on the risk profile of the excavation.
Gas services to individual properties — the pipes connecting a house or business to the distribution main — are a particular risk. These are frequently omitted from BYDA plans, which show the distribution network but not every service connection. The industry standard is to assume a gas service is present in any residential or commercial streetscape until the ground is proved clear.
For assets not shown on any available plan, our underground services not on plans investigation process applies — a combination of GPR, tracer-wire scanning, and targeted non-destructive digging to establish what is actually in the ground.
PE and nylon gas pipes do not conduct an electromagnetic locating signal. A locator may trace an accessible, usable tracer wire installed alongside the pipe. Where the wire is absent or damaged, the team must assess other investigation methods and any targeted exposure against ground conditions, safe access and asset-owner instructions. Confirm the work scope and required permissions before booking.
Tracer wire is a conductive wire installed alongside a non-metallic pipe so a locator can trace a signal from the surface. A broken, inaccessible or missing wire can limit the investigation. Discuss other methods and targeted physical exposure with the team; the appropriate approach depends on site conditions and asset-owner instructions.
Confirm whether the asset is a distribution main, service connection or transmission pipeline, then obtain the owner's conditions for the proposed work. The WorkSafe Victoria and Energy Safe Victoria guide restricts both mechanical and manual excavation near gas assets and specifies written permission for work within relevant restricted areas. Hand digging or vacuum excavation is not automatic permission to work. Confirm clearances, permits and site controls before excavation.
Stop work and evacuate the area if you strike or damage a gas main. Keep people clear and avoid ignition sources, including phones near a gas escape. From a safe location, notify the gas distributor and call 000 if there is immediate danger. Follow the site's emergency plan and do not attempt repairs or re-enter until the relevant authorities say it is safe. The WorkSafe and Energy Safe Victoria guide advises leaving the site undisturbed unless safety requires otherwise.
Lodge a BYDA enquiry before ground disturbance and review the asset-owner responses even if you engage a locator. Plans indicate where services may be and can omit private or unrecorded assets. Compare them with site evidence and report unresolved positions. Locating supports the work plan but does not certify that excavation is safe or replace required permissions and controls.
Expert utility locating services with BYDA certified precision.
Serving projects across Australia with advanced subsurface mapping solutions.